北京现代ix35 2.0排量12年。冷天在外打过把车打淹了。换了新火花塞着火了，20分钟后发动机抖动加不上油，排气管冒出难闻气味，排气管边原有黑灰。把火花塞拆下头部烧黑了。把原车处理一下安装会去也不行。电脑检测不报码。请教 请教一下是怎么回事？谢谢谢谢了

展开

克莱斯勒大捷龙更换中门电吸门锁不用匹配。

根据故障码分析检查发动机电脑的电源线路。发动机电脑在左前杠里边。

你好，克莱斯勒，这款车的整体性能还是不错的，发动机底盘变速箱三大件的整体性能都特别稳定。老款的车型的话，相关的电气原件容易出问题。

CAVITY CIRCUIT FUNCTION 1 A1 B(+) 2 A1 B(+) 3 L43 LEFT LOW BEAM DRIVER 4 L34 RIGHT HIGH BEAM DRIVER 5 L33 LEFT HIGH BEAM DRIVER 6 L44 RIGHT LOW BEAM DRIVER 7 - - 8 Z117, Z118, Z343, Z344 GROUND 9 A1 B(+) 10 FCM 10 HORN RELAY CONTROL 11 - - 12 P201 (EXCEPT EXPORT) ADJUSTABLE PEDALS RELAY CONTROL 13 FCM 13 PARK LAMP RELAY CONTROL 14 FCM 14 FRONT WIPER ON/OFF RELAY CONTROL 15 C41 (DIESEL) CABIN HEATER ASSIST CONTROL 16 W7 FRONT WIPER PARK SWITCH SENSE 17 X3 HORN SWITCH SENSE 18 W1 WASHER FLUID LEVEL SWITCH SENSE 19 FCM 19 FUSED IGNITION SWITCH OUTPUT (START) 20 FCM 20 FUSED B(+) 21 L78 FUSED PARK LAMP RELAY OUTPUT (RIGHT) 22 D25 PCI BUS 23 G931 (DIESEL) AMBIENT TEMPERATURE SENSOR RETURN 24 - - 25 G31 (DIESEL) AMBIENT TEMPERATURE SENSOR SIGNAL 26 L13 (EXPORT) HEADLAMP ADJUST SIGNAL 27 F1, F2 FCM OUTPUT (UNLOCK-RUN-START) 28 - - 29 F100 ORC RUN ONLY DRIVER 30 FCM 30 FRONT/REAR BLOWER MOTOR RELAY CONTROL 31 FCM 31 DEFOGGER RELAY CONTROL 32 FCM 32 (EXPORT) HEADLAMP WASHER RELAY CONTROL 33 FCM 33 FRONT FOG LAMP RELAY CONTROL 34 FCM 34 FRONT WIPER HIGH/LOW RELAY CONTROL 35 FCM 35 ACCESSORY RELAY CONTROL (RUN-ACC) 36 B20 BRAKE FLUID LEVEL SWITCH SENSE 37 F20 FUSED IGNITION SWITCH OUTPUT (RUN-START) 38 A1 B(+) (WHEN IPM C5 CPA IS NOT ENGAGED) 39 T2 (MTX) TRS REVERSE SENSE 40 - - 41 L77 FUSED PARK LAMP RELAY OUTPUT (LEFT) 42 D123 FLASH PROGRAM ENABLE 43 Z116 GROUND 44 L50 (DIESEL) PRIMARY BRAKE SWITCH SIGNAL 44 L50 (GAS) BRAKE LAMP SWITCH OUTPUT 45 W10 FRONT WASHER PUMP MOTOR CONTROL 46 W20 REAR WASHER PUMP MOTOR CONTROL 47 K32 BRAKE TRANSMISSION SHIFT INTERLOCK SOLENOID CONTROL 48 F201 ORC RUN-START DRIVER 49 - - 前控制模块插头信息。不是Can网络。是PCIBUS。后两张图是网络图。

删除 1. 打开引擎盖。 2. 断开并隔离电池负极电缆。 3. 拆卸左四分之一装饰板(请参阅23 -车身/内饰/面板，四分之一装饰板-拆卸)。 4. 断开停车辅助模块电连接器 图1 -停车协助模块电连接器 1 -模块电连接器 2 -停车辅助模块 5. 取下两个连接螺丝，将模块与车辆分离